S-1110P-XT 10/100/1000 Endüstriyel Sıcaklık PoE Medya Dönüştürücüler

S-1110P-XT Endüstriyel Sıcaklık PoE Medya Dönüştürücüleri, ekstrem sıcaklıklarda çalışan 10/100/1000 Ethernet ekipmanını fibere şeffaf biçimde bağlama ihtiyacını karşılarken, standartlara uygun PoE ve PoE+ destekli cihazlara Ethernet Üzerinden Güç (PoE) sağlar. S-1110P-XT PoE Medya Dönüştürücüleri, -40°C ila +75°C (-40°F ila +167°F) arasındaki endüstriyel sınıf sıcaklıklarda çalışır. Trafik yönetimi, petrol ve gaz boru hatları, hava durumu takibi, endüstriyel ve açık hava uygulamalarında bulunan ekipmanların, ticari tip bir medya dönüştürücünün desteklemediği sıcaklıklarda çalışması gerekir. Bu genişletilmiş sıcaklık özelliğinin yanı sıra dayanıklı çelik kasasıyla S-1110P-XT Medya Dönüştürücü; güvenlik kameraları, kablosuz erişim noktaları, alarmlar, trafik kontrolörleri, sensörler ve takip cihazları gibi zorlu ortamlara ve ağır sıcaklık koşullarına maruz kalan iki endüstriyel cihaz arasındaki mesafeyi ekonomik bir şekilde uzatmanın yolunu sunar. Perle PoE Medya Dönüştürücüleri, Güç Kaynağı Ekipmanı (PSE) olarak sınıflandırılır. Ethernet verisini taşıyan standart UTP kabloları kullanırken, Perle PoE medya dönüştürücüleri, IEEE 802.3af PoE standardını (15,4W güç) veya IEEE 802.3at PoE+ standardını (30W güç) destekleyen Güç Alan Cihazlara (PD) da güç sağlayabilir. PoE hakkında daha fazla bilgi edinin.

Ethernet Üzerinden Güç (PSE)
Gelişmiş Güç Yönetimi
PD Güç Sıfırlama
Güç Alan Cihaz Desteği
Güç Kablosu Gerilim Giderme Kayışı
SFP Hız Algılama
Otomatik Anlaşma (802.3u)
Auto-MDIX
Akıllı Bağlantı Geçişi (SmartLink Pass-Through)
Fiber Hata Uyarısı
Duraklatma (IEEE 802.3xy)
Dupleks
Jumbo Paketler
VLAN
Uzaktan Geri Döngü

Özellikler
Sınırlı ömür boyu garanti REACH, RoHS ve WEEE Uyumlu HTSUS Numarası: 8517.62.0020 UNSPSC Kodu: 43201553 ECCN: 5A991
Güç
Giriş Besleme Voltajı PoE models: 46 - 57 vDC PoE+ models: 52 - 57 vDC
Güç Tüketimi 3.5 Watts
Power Over Ethernet (PSE) PoE models: maximum to 15.4 watts PoE+ models: şu değere kadar 30 watts
PoE Options Alternative A (power on pins 1,2 and 3,6) Alternative B (power on pins 4,5 and 7,8) Legacy PoE (IE wireless access points) - (reverse polarity on pins 4,5 and 7,8) Legacy large capacitor detect (pins 4,5 and 7,8)
Güç Konnektörü 2-Pin pluggable terminal block
Göstergeler
Power (PWR) Medya dönüştürücüye güç verildiğinde bu yeşil LED yanar. Aksi halde söner. The LED will blink slowly when either fiber port is in Loopback (Geri Döngü) test mode. The LED will blink quickly if there is a hardware failure where the reason code can be identified through a combination of FDF,LKF, FDC and PSE indicator LEDs
Fiber link on / Receive activity (LKF 1/2) This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the fiber port. If a loss of link on the copport başına results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared.
Copper link on / Receive activity (LKC 1/2) This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the 10/100/1000 UTP port If a loss of link on the copport başına results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared.
Fiber Duplex (FDF 1/2) This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-X link is operational in full duplex mode. The LED is off when in half duplex. If the Auto-Neg switch is turned off, this LED will always be on
Copper Duplex (FDC 1/2) This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is operational in full duplex mode. The LED is off when in half duplex
100/1000 This multi-color LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 1000 Mbps. The LED is yellow when the speed of the copper Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps.
PSE Status (PSE 1/2) This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE; GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied) YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is : Not connected Has not detected a compliant PD and is not applying power PSE has turned off power for Reset function OFF — PSE function switch disabled RED — Blinking: Error Conditions Capacitance too High — 1 blink Resistance too Low or short circuit — 2 blinks Resistance too high or open circuit — 3 blinks
Switch'ler - şasideki yan açıklıktan erişilir
Auto-Negotiation (802.3u) Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex, half duplex, pause and remote fault capabilities. Disabled - The media converter sets the port according to the position of the speed and duplex switches.
Link Mode Link Mode provides a transparency to the state of the copper link allowing for simplified trouble shooting from the devices connected to the media converter. Normal (Default — Up) With Fiber Auto Negotiation enabled when the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault). With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link. Smart Link Pass Through (Down) With Fiber Auto Negotiation enabled the behavior is as follows. When the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault). When Remote Fault (Link Fault) is received on the 1000Base-X interface the copper transmitter will be turned off. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off. With Fiber Auto-Negotiation disabled the behavior is as follows. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off.
Fiber Fault Alert The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled Enabled (Default - Up) When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature. Disabled (Down)
Loopback (Geri Döngü) The media converter can perform a loopback on the 1000Base-X fiber interface. Disabled (Default - Up) Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface.
Speed Copper 100 (Default) 10
Duplex Copper Full (Default) Half
Fiber Negotiation Up: The Media Converter will negotiate Ethernet parameters on the fiber connection. This will ensure that the most optimal connection parameters will be in effect. If connecting to another Perle Media Converter, this parameter should be set to Auto. The Media Converter Module will advertise 1000Mbps, Full and Half Duplex, no Pause. Down: The Media Converter Module’s fiber will be fixed to 1000Mbps, Full Duplex.
Auto-MDIX (Dahili Köprü) Auto-Negotiation (802.3u) etkinse, medya dönüştürücü kullanılacak kablo pin düzenini kendisi belirler on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate. Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting.
PSE Power Settable for each UTP port available. When enabled (UP), the media converter will perform a Power Sourcing Equipment (PSE) function standardına göre IEEE802.3af or 802.3at standartları (relevant model). Default is 'enabled'
PD Power Reset This is a technique to perform a power reset on a PD device(s) attached. When enabled (down), the media converter will upon loss of link on any fiber port, turn off PSE output power to the PD device(s) for 2 seconds then turn the power back on. The power remains on until any fiber link transitions from şu değere kadar down again. With Passthrough enabled (Link Mode enabled and Fiber Auto-Negotiation enabled), a loss of link on the fiber resulting from a loss of link on the copper, a PD Power Reset till still occur. When PD Power Reset disabled, loss of fiber link has no effect on PSE power to the PD device(s).
PoE Power Options (Internal Straps) Set to Alternative A (default): Pins 3,6 Neg, Pins 1,2 Pos Set to Alternative B: Pins 7,8 Neg, Pins 4,5 Pos Set to Legacy Pre-Standard: Pins 7,8 Pos, Pins 4,5 Neg
Konnektörler
10/100/1000Base-T RJ45 connector 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100. 4 pair CAT5 UTP cable for Gigabit.
Manyetik İzolasyon 1.5kv
Fixed Fiber Dual multimode or single mode (Duplex) fiber - SC, ST Single strand fiber (Simplex) - SC LC - obtained by inserting an SFP (LC) in an SFP slot model
Small Form Factor Pluggable (SFP) slot SFP slot models: Empty slot for 100Base-X SFP modules supplied by Perle , Cisco or other manufacturers of MSA compliant SFPs. Hot insertion and removable (hot swappable).
Filtreleme
Filtering 1024 MAC Addresses
Çerçeve (Frame) Özellikleri
Tampon (Buffer) 1000 Kbits çerçeve tampon belleği
Boyut Maksimum çerçeve boyutu: 10,240 bytes -- Gigabit Maksimum çerçeve boyutu: 2048 bytes -- Fast Ethernet
Çevresel Özellikler
Çalışma Sıcaklığı -40°C - 75°C (-40°F - 167°F)
Depolama Sıcaklığı -40°C - 85°C (-40°F - 185°F)
Çalışma Nemi 5% - 90% yoğuşmasız
Depolama Nemi 5% - 95% yoğuşmasız
Çalışma Yüksekliği Up to 3,048 meters (10,000 feet)
Isı Çıkışı (BTU/SAAT) 20.5
MTBF (Hours)* 370,535 Hours (models with fixed fiber ports) 432,168 Hours (models with empty SFP slot) Şu esas alınarak hesaplanmıştır: MIL-HDBK-217-FN2 @ 30°C
Şasi IP20 koruma sınıflı metal
Montaj
DIN Ray Kiti Opsiyonel
Rack Montaj Kiti Opsiyonel
Ürün Ağırlığı ve Boyutları
Ağırlık 0.45 Kg, 1.0 lbs (no power adaptor)
Dimensions 150 x 95 x 26 mm, 5.9 x 3.7 x 1.0 inches
Paketleme
Sevkiyat Ağırlığı 0.52 kg, 1.1 lbs
Sevkiyat Boyutları 150 x 210 x 40 mm, 5.9 x 11 x 2.8 inches
Yasal Onaylar
Emisyonlar FCC Part 15 Class A CISPR 32 / EN 55032 EN61000-3-2
Bağışıklık (Immunity) CISPR 35 / EN 55035
Elektriksel Güvenlik UL/EN/IEC 62368-1 CAN/CSA C22.2 No. 62368-1 UL 60950-1 IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 CE
Lazer Güvenliği EN 60825-1 Bu cihazdaki fiber optik vericiler, şu standarda göre Sınıf 1 Lazer güvenlik gereksinimlerini karşılar: IEC-60825 FDA/CDRH standartları and comply with 21CFR1040.10 and 21CFR1040.11.