S-1110 PoE Medya ve Hız Dönüştürücüleri

Perle’nin özellik açısından zengin Gigabit hız dönüştürmeli PoE Medya Dönüştürücüleri, bakırı fibere şeffaf biçimde bağlarken IP kameralar, VoIP telefonlar ve kablosuz erişim noktaları gibi standart tabanlı PoE ve PoE+ uyumlu cihazlara Power over Ethernet (PoE) sağlar. S-1110 PoE Medya Dönüştürücüleri, Genişletilmiş Sıcaklık aralıkları desteğiyle de mevcuttur. Perle PoE Medya Dönüştürücüleri, Güç Kaynağı Ekipmanı (Power Sourcing Equipment – PSE) olarak sınıflandırılır. Ethernet verisi taşıyan standart UTP kablolar kullanılırken, Perle PoE medya dönüştürücüleri bir veya iki Beslenen Cihaza (Powered Device – PD) da güç sağlayabilir. Perle’nin IEEE 802.3af PoE standardını (15,4W güç) veya IEEE 802.3at PoE+ standardını (30W güç) destekleyen PoE medya dönüştürücü modelleri bulunmaktadır. PoE hakkında daha fazla bilgi edinin. Perle 10/100/1000 PoE Ethernet’ten Fibere Dönüştürücüler, mevcut bir ağın mesafesini fiber kablolama ile genişletmek için ekonomik bir yol sunar. Aynı zamanda bakır UTP kablolama üzerinden IP telefonlar, video konferans ekipmanları, IP kameralar ve Wi-Fi cihazları gibi cihazlara güç sağlayan PoE enjektörleri olarak işlev görürler.

Perle'nin özellik açısından zengin Gigabit hız dönüştürmeli PoE Medya Dönüştürücüleri, bakırı fibere şeffaf biçimde bağlarken IP kameralar, VoIP telefonlar ve kablosuz erişim noktaları gibi standart tabanlı PoE ve PoE+ uyumlu cihazlara Power over Ethernet (PoE) sağlar. S-1110 PoE Medya Dönüştürücüleri, Genişletilmiş Sıcaklık aralıkları desteğiyle de mevcuttur. Perle PoE Medya Dönüştürücüleri, Güç Kaynağı Ekipmanı (Power Sourcing Equipment - PSE) olarak sınıflandırılır. Ethernet verisi taşıyan standart UTP kablolar kullanılırken, Perle PoE medya dönüştürücüleri bir veya iki Beslenen Cihaza (Powered Device - PD) da güç sağlayabilir. Perle'nin IEEE 802.3af PoE standardını (15,4W güç) veya IEEE 802.3at PoE+ standardını (30W güç) destekleyen PoE medya dönüştürücü modelleri bulunmaktadır. PoE hakkında daha fazla bilgi edinin. Perle 10/100/1000 PoE Ethernet'ten Fibere Dönüştürücüler, mevcut bir ağın mesafesini fiber kablolama ile genişletmek için ekonomik bir yol sunar. Aynı zamanda bakır UTP kablolama üzerinden IP telefonlar, video konferans ekipmanları, IP kameralar ve Wi-Fi cihazları gibi cihazlara güç sağlayan PoE enjektörleri olarak işlev görürler.

Power Over Ethernet (PSE)
Gelişmiş Güç Yönetimi
PD Güç Sıfırlama
Beslenen Cihaz Desteği
Çoklu Port Yapılandırmaları
Fiber Yedekliliği
Yedekli Birincil Fiber
Güç Kablosu Gerilim Azaltma Kayışı
SFP Hız Algılama
Otomatik Anlaşma (802.3u)
Otomatik MDIX
Akıllı Bağlantı Aktarımı
Fiber Arıza Uyarısı
Duraklatma (IEEE 802.3xy)
Dupleks
Jumbo Paketler
VLAN
Uzaktan Loopback

Özellikler
Sınırlı ömür boyu garanti REACH, RoHS ve WEEE Uyumlu HTSUS Numarası: 8517.62.0020 UNSPSC Kodu: 43201553 ECCN: 5A991
Güç
Giriş Besleme Voltajı PoE models: 46 - 57 vDC PoE+ models: 52 - 57 vDC
Güç Tüketimi 6 Watts
Power Over Ethernet (PSE) PoE models: maximum to 15.4 watts supplied port başına PoE+ models: şu değere kadar 30 watts supplied port başına
PoE Options Alternative A (power on pins 1,2 and 3,6) Alternative B (power on pins 4,5 and 7,8) Legacy PoE (IE VoIP phones and wireless access points) - (reverse polarity on pins 4,5 and 7,8) Legacy large capacitor detect (pins 4,5 and 7,8)
Güç Konnektörü 5.5mm x 9.5mm x 2.1mm barrel socket
Güç Adaptörü
Universal AC/DC adapter 100-240v AC, regulated 48vDC adapter included for PoE 100-240v AC, regulated 56vDC adapter included for PoE+
Göstergeler
Power (PWR) Medya dönüştürücüye güç verildiğinde bu yeşil LED yanar. Aksi halde söner. The LED will blink slowly when either fiber port is in Loopback (Geri Döngü) test mode. The LED will blink quickly if there is a hardware failure where the reason code can be identified through a combination of FDF,LKF, FDC and PSE indicator LEDs
Fiber link on / Receive activity (LKF 1/2) This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the fiber port. If a loss of link on the copport başına results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared.
Copper link on / Receive activity (LKC 1/2) This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the 10/100/1000 UTP port If a loss of link on the copport başına results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared.
Fiber Duplex (FDF 1/2) This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-X link is operational in full duplex mode. The LED is off when in half duplex. If the Auto-Neg switch is turned off, this LED will always be on
Copper Duplex (FDC 1/2) This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is operational in full duplex mode. The LED is off when in half duplex
100/1000 This multi-color LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 1000 Mbps. The LED is yellow when the speed of the copper Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps.
PSE Status (PSE 1/2) This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE; GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied) YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is : Not connected Has not detected a compliant PD and is not applying power PSE has turned off power for Reset function OFF — PSE function switch disabled RED — Blinking: Error Conditions Capacitance too High — 1 blink Resistance too Low or short circuit — 2 blinks Resistance too high or open circuit — 3 blinks
Switch'ler - şasideki yan açıklıktan erişilir
Auto-Negotiation (802.3u) Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex, half duplex, pause and remote fault capabilities. Disabled - The media converter sets the port according to the position of the speed and duplex switches.
Link Mode Link Mode provides a transparency to the state of the copper link allowing for simplified trouble shooting from the devices connected to the media converter. Normal (Default — Up) With Fiber Auto Negotiation enabled when the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault). With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link. Smart Link Pass Through (Down) With Fiber Auto Negotiation enabled the behavior is as follows. When the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault). When Remote Fault (Link Fault) is received on the 1000Base-X interface the copper transmitter will be turned off. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off. With Fiber Auto-Negotiation disabled the behavior is as follows. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off. Effect on 3 and 4 port units: pass-through conditions will be recognized when the state of her ikisi de copper UTP or fiber port pairs are the same. IE only if her ikisi de copport başınas go down will the fiber port on a 3 port unit be forced inactive.
Fiber Fault Alert The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled Enabled (Default - Up) When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature. Disabled (Down)
Loopback (Geri Döngü) (1/2) The media converter can perform a loopback on the 1000Base-X fiber interface. Disabled (Default - Up) Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface. A loopack switch for each fiber connection On dual fiber units, if one or her ikisi de ports have loopback enable, all copport başınas are disabled, but PoE power is maintained. The other fiber port is unaffected.
Speed Copper 100 (Default) 10
Duplex Copper Full (Default) Half
Fiber Negotiation Up: The Media Converter will negotiate Ethernet parameters on the fiber connection. This will ensure that the most optimal connection parameters will be in effect. If connecting to another Perle Media Converter, this parameter should be set to Auto. The Media Converter Module will advertise 1000Mbps, Full and Half Duplex, no Pause. Down: The Media Converter Module’s fiber will be fixed to 1000Mbps, Full Duplex.
Auto-MDIX (Dahili Köprü) Auto-Negotiation (802.3u) etkinse, medya dönüştürücü kullanılacak kablo pin düzenini kendisi belirler on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate. Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting.
PSE Power Settable for each UTP port available. When enabled (UP), the media converter will perform a Power Sourcing Equipment (PSE) function standardına göre IEEE802.3bt standard. Default is 'enabled'
PD Power Reset This is a technique to perform a power reset on a PD device(s) attached. When enabled (down), the media converter will upon loss of link on any fiber port, turn off PSE output power to the PD device(s) for 2 seconds then turn the power back on. The power remains on until any fiber link transitions from şu değere kadar down again. With Passthrough enabled (Link Mode enabled and Fiber Auto-Negotiation enabled) , a loss of link on the fiber resulting from a loss of link on the copper, a PD Power Reset till still occur. When PD Power Reset disabled, loss of fiber link has no effect on PSE power to the PD device(s).
Fiber Redundancy (Dual Fiber Models) When disabled (default), the ports will operate as a 3 or 4 port switch When enabled (Down) the media converter treats Fiber 1 as the primary. If the link fails, the fiber link is switched over to fiber 2 within 50ms. While the primary is active, the link on port 2 will be maintained, but the port will not pass data A redundancy switch-over will not occur if the fiber link was brought down as a result of link pass-through from a copport başına.
Redundant Primary (Dual Fiber Models) If the 'Fiber Redundancy' feature is also enabled, the primary fiber 1 link is continuously monitored and if is restored for at least 6 seconds, the link will be switched back from the secondary fiber 2 port to the primary fiber 1 port
PoE Power Options (Internal Straps) Set to Alternative A (default): Pins 3,6 Neg, Pins 1,2 Pos Set to Alternative B: Pins 7,8 Neg, Pins 4,5 Pos Set to Legacy Pre-Standard: Pins 7,8 Pos, Pins 4,5 Neg
Konnektörler
10/100/1000Base-T 1 or 2 RJ45 connectors. 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100. 4 pair CAT5 UTP cable for Gigabit.
Manyetik İzolasyon 1.5kv
Fixed Fiber Available on single fiber port models with 1 or 2 copper UTP ports Dual multimode or single mode (Duplex) fiber - SC, ST Single strand fiber (Simplex) - SC LC - obtained by inserting an SFP (LC) in an SFP slot model
Small Form Factor Pluggable (SFP) slot SFP slot models: Empty slot for 1000Base-X or 100Base-X SFP modules supplied by Perle , Cisco or other manufacturers of MSA compliant SFPs. Hot insertion and removable (hot swappable).
Filtreleme
Filtering 1024 MAC Addresses
Çerçeve (Frame) Özellikleri
Tampon (Buffer) 1000 Kbits çerçeve tampon belleği
Boyut Maksimum çerçeve boyutu: 10,240 bytes -- Gigabit Maksimum çerçeve boyutu: 2048 bytes -- Fast Ethernet
Çevresel Özellikler
Çalışma Sıcaklığı 0°C - 50°C (32°F - 122°F)
Depolama Sıcaklığı minimum aralık: -25°C - 70°C (-13°F - 158°F)
Çalışma Nemi 5% - 90% yoğuşmasız
Depolama Nemi 5% - 95% yoğuşmasız
Çalışma Yüksekliği Up to 3,048 meters (10,000 feet)
Isı Çıkışı (BTU/SAAT) 20.5 BTU/hr
MTBF (Hours)* Model Type : 1 UTP Fixed Fiber - No Power Adaptor : 361190 Hrs - PoE : 206434 Hrs - PoE+ : 78317 Hrs Model Type : 1 UTP, 1 SFP - No Power Adaptor : 410,188 Hrs - PoE : 221,560 Hrs - PoE+ : 80,399 Hrs Model Type : 1 UTP, 2 SFP - No Power Adaptor : 399,432 Hrs - PoE : 218,384 Hrs - PoE+ : 79,977 Hrs Model Type : 2 UTP, fixed fiber - No Power Adaptor : 292,529 Hrs - PoE : 182,017 Hrs - PoE+ : 74,524 Hrs Model Type : 2 UTP, 1 SFP - No Power Adaptor : 323,861 Hrs - PoE : 193,675 Hrs - PoE+ : 76,407 Hrs Model Type : 2 UTP, 2 SFP - No Power Adaptor : 317,119 Hrs - PoE : 191,244 Hrs - PoE+ : 76,026 Hrs
Şasi IP20 koruma sınıflı metal
Montaj
DIN Ray Kiti Opsiyonel
Rack Montaj Kiti Opsiyonel
Ürün Ağırlığı ve Boyutları
Ağırlık 0.45 Kg, 1.0 lbs (no power adaptor)
Dimensions 150 x 95 x 26 mm, 5.9 x 3.7 x 1.0 inches
Paketleme
Sevkiyat Ağırlığı PoE models: 1.1 Kg, 2.4 lbs PoE+ models: 1.4 Kg, 3.1 lbs
Sevkiyat Boyutları 300 x 200 x 70 mm, 11.8 x 7.9 x 2.8 inches
Yasal Onaylar
Emisyonlar FCC Part 15 Class A CISPR 32 / EN 55032 EN61000-3-2
Bağışıklık (Immunity) CISPR 35 / EN 55035
Elektriksel Güvenlik UL/EN/IEC 62368-1 CAN/CSA C22.2 No. 62368-1 UL 60950-1 IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 CE
Lazer Güvenliği EN 60825-1 Bu cihazdaki fiber optik vericiler, şu standarda göre Sınıf 1 Lazer güvenlik gereksinimlerini karşılar: IEC-60825 FDA/CDRH standartları and comply with 21CFR1040.10 and 21CFR1040.11.