SR-1110-XT DIN Rail Media Converters

PerleSR-1110-XT DIN Rail Media Converterstransparently connect UTP copper to fiber in industrial grade operating temperatures-40F to +167F (-40C to +75C). Equipment found intraffic management, oil and gas pipelines, weather tracking, industrial and outdoor applicationsmust function in temperatures that cannot be supported by a commercial based media converter. TheseRate Converting Media Convertersare ideal for use with industrial devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.

An SR-1110-XT Media Converter is also available withan SFP slot.

Network Administrators can “see-everything” with Perle’s advanced features such as Auto-Negotiation, Auto-MDIX, Link Pass-Through, Far End Fault, and Pause which make the end to end link completely transparent. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, makeSR-1110-XT Rate Converting Media Convertersthe smart choice for IT professionals.

An SR-1110-XT Media Converter is also available withan SFP slot.

Network Administrators can "see-everything" with Perle's advanced features such as Auto-Negotiation, Auto-MDIX, Link Pass-Through, Far End Fault, and Pause which make the end to end link completely transparent. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, makeSR-1110-XT Rate Converting Media Convertersthe smart choice for IT professionals.

Fully designed to operate in extreme temperatures
DIN Rail Enclosure
Auto-Negotiation
Auto-MDIX
Smart Link Pass-Through
Fiber Fault Alert
Pause (IEEE 802.3xy)
Duplex
Jumbo Packets
VLAN
Remote LoopBack

Specifications
Lifetime limited warranty Reach, RoHS and WEEE Compliant HTSUS Number: 8517.62.0020 UNSPSC Code: 43201553 ECCN: 5A991
Power
Input Supply Voltage Triple voltage 12 / 24 / 48 VDC (9.6 – 60 VDC) input supporting: 2 x Terminal Block power input and 1 x T-Bus power input
Current 0.09 A (@ 24VDC)
Power Consumption 2.16 watts (@ 24VDC)
Power Connector Dual input Terminal Block and/or T-Bus
Indicators
Power / TST This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink fast/slow when in Loopback test mode or hardware error.
Fiber link on / Receive activity (LKF) On: Fiber link present. Blinking slowly: Fiber link disabled because of copper link loss. Blinking quickly: Fiber link present and receiving data. Off: No fiber link present
Copper link on / Receive activity (LKC) On: Fiber link present. Blinking slowly: Fiber link disabled because of copper link loss. Blinking quickly: Fiber link present and receiving data. Off: No fiber link present
Link Pass-Through (LKP) On: Copper link is present. Blinking slowly: Copper link disabled because of fiber link loss. Blinking quickly: Copper link present and receiving data. Off: No copper link present
10/100/1000 Copper Speed (SP) Green: 1000 Mbps Yellow: 100 Mbps Off: 10 Mbps
Copper Link Activity (LK) On: Copper link is present Blinking quickly: Copper link receiving data
Switches - accessible by sliding the chassis open
Auto-Negotiation Auto (Default-Up): In this mode of operation the media converter will negotiate Ethernet parameters on both the copper and the fiber connection. This will ensure the most optimal connection parameters will be in effect. If connecting to another Perle Gigabit Media Converter, this parameter should be set to Auto. Off: Copper Negotiation should only be turned off, if the copper link partner does not support copper link negotiations.
Smart Link Pass-Through Smart Link Pass-Through (Default-Up): In this mode, the link state on one connection is directly reflected through the media converter to the other connection. If link is lost on one of the connections, then the other link will be brought down by the media converter. If the installation has a media converter on both ends of the fiber link and both are setup for Smart Link Pass-Through, then a loss of copper link on the far end device will propagate through both media converters and will result in a loss of link at the near end device. This would, therefore, resemble a direct copper connection. Standard Mode (Down): In this mode the links on the fiber and copper sides can be brought up and down independently of each other. A loss of link on either the fiber link or copper link can take place without affecting the other connection.
Loopback Disabled (Default-Up): The loopback feature is disabled. This is the normal position for regular operation. The switch must be set to this position for data to pass through the media converter. Enabled: This is a test mode. All data received on the receive (RX) fiber connection is looped back to the transmit (TX) fiber connection. The state of the copper is not relevant and no data or link status is passed through to the copper side.
Fiber Fault Alert Enabled (Default-Up): In this mode, when Fiber negotiation is turned on, if the media converter detects a loss of fiber signal on the fiber receiver it will immediately disable its fiber transmitter signal. This notifies the fiber link partner that an error condition exists on the fiber connection. If the remote media converter is set up for FFA Enabled and the local media converter is set up with Smart Link Pass-Through, a loss of fiber link on either the transmit or receive line will be passed through to the local copper connection to notify the connected device. If the media converter has been set to Smart Link Pass-Through mode, the effect will be the same as FFA since the link loss on the fiber receiver will result in bringing down the copper link, which will in turn cause the transmit fiber link to be brought down. Disabled: In this mode, the media converter will not monitor for fiber fault.
Duplex Mode Full (Default-Up): In this mode, when Auto Negotiation is set to off, the media converter will be set to Full Duplex mode. Half: The media converter will be set to Half Duplex mode
Copper Speed 100 (Default-Up): In this mode, when Auto Neg (copper) is set to off, the media converter will use this switch setting for its Ethernet copper speed connection.The media converter will force the speed to 100 Mbps. 10: The media converter will force the speed to 10 Mbps
Cables and Connectors
10/100/1000Base-T RJ45 connector 2 pair CAT 5 (UTP or STP) or better cable for 10/100 Mbps 4 pair CAT 5 (UTP or STP) or better cable for 10/100/1000 Mbps
Fixed Fiber Dual multimode or single mode ( Duplex ) fiber - SC, ST Single strand fiber ( Simplex ) – SC
Magnetic Isolation 1.5kv
Fiber Optic Cable Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron Single Mode: 9/125 micron (ITu-T 625)
Filtering
Filtering 1024 MAC Addresses
Frame Specifications
Buffer 1000 Kbits frame buffer memory
Size Maximum frame size of 10,240 bytes -- Gigabit Maximum frame size of 2048 bytes -- Fast Ethernet
Packet Transmission Characteristics
Bit Error Rate (BER) <10 -12
Environmental Specifications
Operating Temperature -40°C to 75°C (-40°F to 167°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Operating Humidity 5% to 90% non-condensing
Storage Humidity 5% to 95% non-condensing
Operating Altitude Up to 3,048 meters (10,000 feet)
Heat Output (BTU/HR) 7.37
MTBF (Hours)* 564,766 Hours Calculation model based on MIL-HDBK-217-FN2 @ 30°C
Chassis Molded plastic DIN Rail case with an IP20 ingress protection rating
Mounting
Din Rail Kit Native
Product Weight and Dimensions
Weight 0.12 kg, 0.26 lbs
Dimensions 114 x 100 x 22.5mm, 4.5 x 3.9 x 0.88 inches
Packaging
Shipping Weight 0.17 kg, 0.37 lbs
Shipping Dimensions 145 x 105 x 30 mm, 5.7 x 4.1 x 1.2 inches
Regulatory Approvals
Emissions FCC 47 Part 15 Class A EN55011 (CISPR11) ICES-003 EN61000-6-4 (Emissions for industrial environments) CISPR 32 / EN 55032 EN61000-3-2
Immunity CISPR 35 / EN 55035 EN 61000-4-2 (ESD) EN 61000-4-3 (RS) EN 61000-4-4 (EFT) EN 61000-4-5 (Surge) EN 61000-4-6 (CS) EN 61000-4-8 (PFMF) EN 61000-4-11 IEC/EN 61000-6-2 (General Immunity for Industrial Environments)
Safety UL/EN/IEC 62368-1 (previously 60950-1) CAN/CSA C22.2 No. 62368-1 CE
Laser Safety EN 60825-1 Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11.