S-1110P-XT 10/100/1000 Industrial Temperature PoE Media Converters

TheS-1110P-XT Industrial Temperature PoE Media Convertersaddress the need for transparently connecting 10/100/1000 Ethernet equipment that operate in extreme temperatures to fiber while providing Power over Ethernet (PoE) to standards-based PoE and PoE+ compliant devices.

The S-1110P-XT PoE Media Converters will operate in industrial grade temperatures of-40°F to +167°F (-40°C to +75°C). Equipment found intraffic management, oil and gas pipelines, weather tracking, industrial and outdoor applicationsmust function in temperatures that cannot be supported by a commercial based media converter. Boasting this extended temperature feature along with a rugged steel casing, the S-1110P-XT Media Converter provides an economical path to extend the distance between two industrial devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.

PerlePoE Media Convertersare classified as Power Sourcing Equipment (PSE). While using standard UTP cables that carry Ethernet data, Perle PoE media converters can also provide power to Powered Devices (PDs) that support the IEEE 802.3af PoE standard (15.4W of power) or the IEEE 802.3at PoE+ standard (30W of power).Learn more about PoE.

Power Over Ethernet(PSE)
Advanced Power Management
PD Power Reset
Powered Device Support
Power Strain Relief strap
SFP Speed Sensing
Auto-Negotiation (802.3u)
Auto-MDIX
SmartLink Pass-Through
Fiber Fault Alert
Pause (IEEE 802.3xy)
Duplex
Jumbo Packets
VLAN
Remote Loopback

Specifications
Lifetime limited warranty Reach, RoHS and WEEE Compliant HTSUS Number: 8517.62.0020 UNSPSC Code: 43201553 ECCN: 5A991
Power
Input Supply Voltage PoE models: 46 - 57 vDC PoE+ models: 52 - 57 vDC
Power Consumption 3.5 Watts
Power Over Ethernet (PSE) PoE models: maximum to 15.4 watts PoE+ models: up to 30 watts
PoE Options Alternative A (power on pins 1,2 and 3,6) Alternative B (power on pins 4,5 and 7,8) Legacy PoE (IE wireless access points) - (reverse polarity on pins 4,5 and 7,8) Legacy large capacitor detect (pins 4,5 and 7,8)
Power Connector 2-Pin pluggable terminal block
Indicators
Power (PWR) This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when either fiber port is in Loopback test mode. The LED will blink quickly if there is a hardware failure where the reason code can be identified through a combination of FDF,LKF, FDC and PSE indicator LEDs
Fiber link on / Receive activity (LKF 1/2) This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the fiber port. If a loss of link on the copper port results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared.
Copper link on / Receive activity (LKC 1/2) This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the 10/100/1000 UTP port If a loss of link on the copper port results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared.
Fiber Duplex (FDF 1/2) This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-X link is operational in full duplex mode. The LED is off when in half duplex. If the Auto-Neg switch is turned off, this LED will always be on
Copper Duplex (FDC 1/2) This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is operational in full duplex mode. The LED is off when in half duplex
100/1000 This multi-color LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 1000 Mbps. The LED is yellow when the speed of the copper Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps.
PSE Status (PSE 1/2) This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE; GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied) YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is : Not connected Has not detected a compliant PD and is not applying power PSE has turned off power for Reset function OFF — PSE function switch disabled RED — Blinking: Error Conditions Capacitance too High — 1 blink Resistance too Low or short circuit — 2 blinks Resistance too high or open circuit — 3 blinks
Switches - accessible through a side opening in the chassis
Auto-Negotiation (802.3u) Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex, half duplex, pause and remote fault capabilities. Disabled - The media converter sets the port according to the position of the speed and duplex switches.
Link Mode Link Mode provides a transparency to the state of the copper link allowing for simplified trouble shooting from the devices connected to the media converter. Normal (Default — Up) With Fiber Auto Negotiation enabled when the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault). With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link. Smart Link Pass Through (Down) With Fiber Auto Negotiation enabled the behavior is as follows. When the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault). When Remote Fault (Link Fault) is received on the 1000Base-X interface the copper transmitter will be turned off. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off. With Fiber Auto-Negotiation disabled the behavior is as follows. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off.
Fiber Fault Alert The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled Enabled (Default - Up) When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature. Disabled (Down)
Loopback The media converter can perform a loopback on the 1000Base-X fiber interface. Disabled (Default - Up) Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface.
Speed Copper 100 (Default) 10
Duplex Copper Full (Default) Half
Fiber Negotiation Up: The Media Converter will negotiate Ethernet parameters on the fiber connection. This will ensure that the most optimal connection parameters will be in effect. If connecting to another Perle Media Converter, this parameter should be set to Auto. The Media Converter Module will advertise 1000Mbps, Full and Half Duplex, no Pause. Down: The Media Converter Module’s fiber will be fixed to 1000Mbps, Full Duplex.
Auto-MDIX (Internal Strap) If Auto-Negotiation (802.3u) is enabled, the media converter determines the current cable pinout to use on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate. Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting.
PSE Power Settable for each UTP port available. When enabled (UP), the media converter will perform a Power Sourcing Equipment (PSE) function as per IEEE802.3af or 802.3at standards (relevant model). Default is 'enabled'
PD Power Reset This is a technique to perform a power reset on a PD device(s) attached. When enabled (down), the media converter will upon loss of link on any fiber port, turn off PSE output power to the PD device(s) for 2 seconds then turn the power back on. The power remains on until any fiber link transitions from up to down again. With Passthrough enabled (Link Mode enabled and Fiber Auto-Negotiation enabled), a loss of link on the fiber resulting from a loss of link on the copper, a PD Power Reset till still occur. When PD Power Reset disabled, loss of fiber link has no effect on PSE power to the PD device(s).
PoE Power Options (Internal Straps) Set to Alternative A (default): Pins 3,6 Neg, Pins 1,2 Pos Set to Alternative B: Pins 7,8 Neg, Pins 4,5 Pos Set to Legacy Pre-Standard: Pins 7,8 Pos, Pins 4,5 Neg
Connectors
10/100/1000Base-T RJ45 connector 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100. 4 pair CAT5 UTP cable for Gigabit.
Magnetic Isolation 1.5kv
Fixed Fiber Dual multimode or single mode (Duplex) fiber - SC, ST Single strand fiber (Simplex) - SC LC - obtained by inserting an SFP (LC) in an SFP slot model
Small Form Factor Pluggable (SFP) slot SFP slot models: Empty slot for 100Base-X SFP modules supplied by Perle , Cisco or other manufacturers of MSA compliant SFPs. Hot insertion and removable (hot swappable).
Filtering
Filtering 1024 MAC Addresses
Frame Specifications
Buffer 1000 Kbits frame buffer memory
Size Maximum frame size of 10,240 bytes -- Gigabit Maximum frame size of 2048 bytes -- Fast Ethernet
Environmental Specifications
Operating Temperature -40°C to 75°C (-40°F to 167°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Operating Humidity 5% to 90% non-condensing
Storage Humidity 5% to 95% non-condensing
Operating Altitude Up to 3,048 meters (10,000 feet)
Heat Output (BTU/HR) 20.5
MTBF (Hours)* 370,535 Hours (models with fixed fiber ports) 432,168 Hours (models with empty SFP slot) Calculation model based on MIL-HDBK-217-FN2 @ 30°C
Chassis Metal with an IP20 ingress protection rating
Mounting
Din Rail Kit Optional
Rack Mount Kit Optional
Product Weight and Dimensions
Weight 0.45 Kg, 1.0 lbs (no power adaptor)
Dimensions 150 x 95 x 26 mm, 5.9 x 3.7 x 1.0 inches
Packaging
Shipping Weight 0.52 kg, 1.1 lbs
Shipping Dimensions 150 x 210 x 40 mm, 5.9 x 11 x 2.8 inches
Regulatory Approvals
Emissions FCC Part 15 Class A CISPR 32 / EN 55032 EN61000-3-2
Immunity CISPR 35 / EN 55035
Electrical Safety UL/EN/IEC 62368-1 CAN/CSA C22.2 No. 62368-1 UL 60950-1 IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 CE
Laser Safety EN 60825-1 Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11.