eXP-S110-XT PoE Fast Ethernet Extenders

PerleeXP-S110-XT PoE Fast Ethernet Extenderstransparently extend Ethernet beyond the general limits of 328ft / 100mwhile providing Power over Ethernet (PoE)to standards-based compliant devices such as IP cameras and wireless access points located inextreme temperature environments.

This technology enables users to transparentlyextend up to four 10/100 Power over Ethernet connectionsacross copper wiring. Use single twisted pair (CAT5/6/7), coax or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.

At the central site, the 10/100 Ethernet Extender has full PoE support andoperates as a Powered Device (PD)under IEEE 802.3af supporting end-span and mid-span power sources (PSE). The PoE Ethernet Extender at the central site then transmits power over the copper wire to power the remote PoE Ethernet Extender and attached PD. The remote PoE Ethernet Extenders areclassified as Power Sourcing Equipment (PSE). While using standard UTP cables that carry Ethernet data, Perle eXP-S110-XT PoE Ethernet Extendersprovide up to 15.4 watts of powerto Powered Devices (PDs). For longer distance applications the remote PoE Extender (CPE) can be powered by a local 48v adapter.Learn more about PoE.

Extend Ethernet over twisted pair
Extend Ethernet over Coaxial cable
On-board PoE Power Controller
Advanced Power capabilities
Fully compliant 802.3af PoE PSE
Fully Compliant 802.3af/at PoE PD
PSE Status Indicator
PD Power Reset (Port 1)
Power Multiplier Selection
Broadest range of PoE devices supported
High-Speed Performance
Plug and Play operation
Link Pass-Through*
Interlink Fault Feedback*
Auto-Negotiation
Auto-MDIX
Fixed Speed and Duplex
VLAN
Transparent to IP Video compression protocols
Power Strain Relief strap

High Speed Asymmetric
Reach (Distance)		VDSL Rate (Mbps)
feet	meters	Downstream	Upstream
500	152	101	92
1000	305	101	63
1500	457	90	38
2000	610	62	24
2500	762	55	10
3000	914	42	5
3500	1000	35	3

High Speed Symmetric
Reach (Distance)		VDSL Rate (Mbps)
feet	meters	Downstream	Upstream
500	152	101	101
1000	305	85	101
1500	457	62	47
2000	610	60	29
2500	762	44	14
3000	914	30	7
3500	1000	29	4

Long Reach Symmetric
Reach (Distance)		VDSL Rate (Mbps)
feet	meters	Downstream	Upstream
500	152	53	44
1000	305	53	43
2500	762	39	18
4000	1219	25	4
5500	1676	17	1.9
7000	2134	8	2.3
7500	2286	7	2.2
8000	2438	5	2.2

Long Reach Asymmetric
Reach (Distance)		VDSL Rate (Mbps)
feet	meters	Downstream	Upstream
500	152	78	16
1000	305	78	16
2500	762	55	10
4000	1219	31	0.8
5500	1676	20	0.6
7000	2134	11	0.6
7500	2286	10	0.6
8000	2438	8	0.6

Specifications
Lifetime limited warranty Reach, RoHS and WEEE Compliant HTSUS Number: 8517.62.0020 UNSPSC Code: 43222608 ECCN: 5A991
Remote (Power over Ethernet) Local (power over link - VDSL)
Power
Unit Powered by eXP-1S110E-XT Local power adapter or VDSL eXP-4S110E-XT Local power adapter or VDSL eXP-1S110L-XT Local power adapter or PoE Power Sourcing Equipment such as a Cisco PoE+ Switch on port #1 PoE+ power injector eXP-4S110L-XT Local power adapter or PoE Power Sourcing Equipment such as a Cisco PoE+ Switch on port #1 PoE+ power injector
Provides Power to: eXP-1S110E-XT Ethernet eXP-4S110E-XT Ethernet eXP-1S110L-XT Link (VDSL Interlink) eXP-4S110L-XT Link (VDSL Interlink)
Power adapter connector Barrel or terminal block
Input Voltage Range from adapter eXP-1S110E-XT 46V to 57 eXP-4S110E-XT 46V to 57 eXP-1S110L-XT 29 to 57 eXP-4S110L-XT 29 to 57
Input Voltage Range from VDSL (parasitic) eXP-1S110E-XT 24 to 57 eXP-4S110E-XT 24 to 57 eXP-1S110L-XT N/A eXP-4S110L-XT N/A
Power Connectors 5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block
Remote (Power over Ethernet) Local (power over link - VDSL)
Ethernet
10/100Base TX Port(s) eXP-1S110E-XT 1 port RJ45 Shielded eXP-4S110E-XT 4 port RJ45 Shielded eXP-1S110L-XT 1 port RJ45 Shielded eXP-1S110L-XT 4 port RJ45 Shielded
Auto-MDIX Auto-MDIX enables proper operation with either straight-through or crossover cabling
Distance Distance up to 100 meters (328 feet) as per IEEE 802.3
Maximum Frame Size 1522
Type of PoE device eXP-1S110E-XT PSE (PoE) IEEE 802.3af eXP-4S110E-XT PSE (PoE) IEEE 802.3af eXP-1S110L-XT PD (Class 0 or 4 device) eXP-4S110L-XT PD (Class 0 or 4 device)
PoE PSE Power Budget eXP-1S110E-XT Refer to the Power Reach Installation Planning Guide eXP-4S110E-XT Refer to the Power Reach Installation Planning Guide eXP-1S110L-XT N/A eXP-4S110L-XT N/A
PoE PSE RJ45 Cable Pinout eXP-1S110E-XT Alternative A (default) on all ports Pins 3,6 Neg, Pins 1,2 Pos Alternative B: selectable on port #1 Pins 7,8 Neg, Pins 4,5 Pos Legacy Cisco Pre-Standard: selectable on port #1 Pins 7,8 Pos, Pins 4,5 Neg eXP-4S110E-XT Alternative A (default) on all ports Pins 3,6 Neg, Pins 1,2 Pos Alternative B: selectable on port #1 Pins 7,8 Neg, Pins 4,5 Pos Legacy Cisco Pre-Standard: selectable on port #1 Pins 7,8 Pos, Pins 4,5 Neg eXP-1S110L-XT N/A eXP-4S110L-XT N/A
Remote (Power over Ethernet) Local (power over link - VDSL)
VDSL – Interlink
RJ45, BNC, Terminal Block Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted. TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector: RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B) BNC – Coaxial 50 and 75 ohm cable with BNC connector Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 (0.9 mm) and 26 AWG (0.44 mm).
Power Injection over the Interlink (VDSL) – 2-wire eXP-1S110E-XT N/A eXP-4S110E-XT N/A eXP-1S110L-XT Injects SELV compliant voltage and VDSL data across a single pair of cooper wires (pins 4 and 5) or 2 conductor BNC coaxial cable eXP-4S110L-XT Injects SELV compliant voltage and VDSL data across a single pair of cooper wires (pins 4 and 5) or 2 conductor BNC coaxial cable
Short Circuit Protection eXP-1S110E-XT N/A eXP-4S110E-XT N/A eXP-1S110L-XT Short Circuit protection provided eXP-4S110L-XT Short Circuit protection provided
Reverse Polarity Protection eXP-1S110E-XT The voltage from the VDSL link requires proper polarity in order to provide power to the remote extender. Reverse polarity protection however will ensure that there is no damage to the extender eXP-4S110E-XT The voltage from the VDSL link requires proper polarity in order to provide power to the remote extender. Reverse polarity protection however will ensure that there is no damage to the extender eXP-1S110L-XT N/A eXP-4S110L-XT N/A
Power Multiplier Selection When used with 4-pair cable such as CAT5 on the VDSL Interlink port, an optional internal strap selection on the Ethernet Extender will provide VDSL transmission data on 1 pair and power across the 3 other pairs enabling even greater distances for power transmission to be achieved
VDSL2 Line Rate/Reach Actual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG (0.5 MM) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models High Speed Asymmetric Reach (Distance) VDSL Rate (Mbps) feet meters Downstream Upstream 500 152 101 92 1000 305 101 63 1500 457 90 38 2000 610 62 24 2500 762 55 10 3000 914 42 5 3500 1000 35 3 High Speed Symmetric Reach (Distance) VDSL Rate (Mbps) feet meters Downstream Upstream 500 152 101 101 1000 305 85 101 1500 457 62 47 2000 610 60 29 2500 762 44 14 3000 914 30 7 3500 1000 29 4 Long Reach Symmetric Reach (Distance) VDSL Rate (Mbps) feet meters Downstream Upstream 500 152 53 44 1000 305 53 43 2500 762 39 18 4000 1219 25 4 5500 1676 17 1.9 7000 2134 8 2.3 7500 2286 7 2.2 8000 2438 5 2.2 Long Reach Asymmetric Reach (Distance) VDSL Rate (Mbps) feet meters Downstream Upstream 500 152 78 16 1000 305 78 16 2500 762 55 10 4000 1219 31 0.8 5500 1676 20 0.6 7000 2134 11 0.6 7500 2286 10 0.6 8000 2438 8 0.6 This table applies when the power multiplier option is selected
Power Budget for Power over VDSL The amount of available power at the PoE PD is dependent on the scenario planned. Refer to the Power Reach Installation Planning Guide
Indicators
Power / TST This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - Local Ethernet Extender is operating in CO VDSL mode
CPE - remote Ethernet Extender is operating in CPE VDSL mode
ILNK Indicates Link Status and activity on the Interlink (VDSL) port
ETH Indicates link status and activity on Ethernet port(s).
Remote (Power over Ethernet) Local (power over link - VDSL)
PSE Status eXP-1S110E-XT This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE; GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied) YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is : Not connected Has not detected a compliant PD and is not applying power PSE has turned off power for Reset function OFF — PSE function switch disabled RED — Blinking: Error Conditions Capacitance too High — 1 blink Resistance too Low or short circuit — 2 blinks Resistance too high or open circuit — 3 blinks eXP-4S110E-XT This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE; GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied) YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is : Not connected Has not detected a compliant PD and is not applying power PSE has turned off power for Reset function OFF — PSE function switch disabled RED — Blinking: Error Conditions Capacitance too High — 1 blink Resistance too Low or short circuit — 2 blinks Resistance too high or open circuit — 3 blinks eXP-1S110L-XT N/A eXP-4S110L-XT N/A
Switches
Access Switch settings are accessible through a side opening in the chassis
Rate/Reach Two switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise Ratio Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u) control on Port 1 Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100Base-TX interface. It is set to advertise full duplex. Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.
Force Ethernet Speed on Port 1 When Auto-Negotiation switch is disabled, a fixed speed can be forced on port 1 to 100 (Default) or 10
Force Ethernet Duplex on Port 1 When Auto-Negotiation switch is disabled, Full or half Duplex can be forced on port 1 to Full (Default) or Half
Link Mode Standard (Default) - The 10/100Base-TX link remains active independent of the state of the Ethernet link on its remote peer. Link Pass-Through - state of the 10/100Base-TX Ethernet connection is “passed through” or propagated across the VDSL link to the 10/100Base-TX Ethernet link on its remote Ethernet Extender peer.
Interlink Fault Feedback Enabled – A loss of VDSL link will drop the 10/100 Ethernet port on each end until the link recovers Disabled (Default) - The state of the VDSL link is not propagated to the 10/100Base-TX port
Loopback Enabled – The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its remote peer. Disabled (Default - Up)
Remote (Power over Ethernet) Local (power over link - VDSL)
PoE PD Class selection eXP-1S110E-XT N/A eXP-4S110E-XT N/A eXP-1S110L-XT (Internal strap) for PoE PD classification type identification for attached IEEE 802.3at compliant PoE+ switch on port #1 Class 0 – PoE PD device - 0.44-12.94W (Default) Class 4 – PoE+ PD device 12.95 – 25.5W eXP-4S110L-XT (Internal strap) for PoE PD classification type identification for attached IEEE 802.3at compliant PoE+ switch on port #1 Class 0 – PoE PD device - 0.44-12.94W (Default) Class 4 – PoE+ PD device 12.95 – 25.5W
PD Reset (Port 1) eXP-1S110E-XT When enabled (down), the Ethernet Extender will upon loss of link on the VDSL Interlink port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until the VDSL link transitions from up to down again. When PD Power Reset is disabled (default), loss of VDSL link has no effect on power supplied to the PD. eXP-4S110E-XT When enabled (down), the Ethernet Extender will upon loss of link on the VDSL Interlink port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until the VDSL link transitions from up to down again. When PD Power Reset is disabled (default), loss of VDSL link has no effect on power supplied to the PD. eXP-1S110L-XT N/A eXP-4S110L-XT N/A
Environmental Specifications
Operating Temperature -40°C to 75°C (-40°F to 167°F)
Storage Temperature minimum range of -40°C to 75°C (-40°F to 167°F)
Operating Humidity 5% to 90% non-condensing
Storage Humidity 5% to 95% non-condensing
Operating Altitude Up to 3,048 meters (10,000 feet)
Remote (Power over Ethernet) Local (power over link - VDSL)
Current mA eXP-1S110E-XT 108 @ 48vdc eXP-4S110E-XT 121 @ 48vdc eXP-1S110L-XT 129 @ 48vdc eXP-4S110L-XT 142 @ 48vdc
Unit Power Consumption watts eXP-1S110E-XT 5.2 eXP-4S110E-XT 5.8 eXP-1S110L-XT 6.2 eXP-4S110L-XT 6.8
Heat Output (BTU/HR) eXP-1S110E-XT 17.74 eXP-4S110E-XT 19.79 eXP-1S110L-XT 21.16 eXP-4S110L-XT 23.20
MTBF with power adapter (Hours)* N/A
MTBF without power adapter (Hours)* eXP-1S110E-XT 300,172 Hours eXP-4S110E-XT 262,530 Hours eXP-1S110L-XT 339,780 Hours eXP-4S110L-XT 294,389 Hours
Calculation model based on MIL-HDBK-217-FN2 @ 30°C
Mounting
Wall/Desk Standard
Din Rail Kit Optional
Rack Mount Kit Optional
Remote (Power over Ethernet) Local (power over link - VDSL)
Product Weight and Dimensions
Weight eXP-1S110E-XT 0.58 Kg, 1.3 lbs eXP-4S110E-XT 0.61Kg, 1.34 lbs eXP-1S110L-XT 0.58 Kg, 1.3 lbs eXP-4S110L-XT 0.61Kg, 1.34 lbs
Dimensions 163 x 116 x 37 mm, 6.4 x 4.6 x 1.46 inches
Remote (Power over Ethernet) Local (power over link - VDSL)
Packaging
Shipping Weight eXP-1S110E-XT 0.79 Kg, 1.7 lbs eXP-4S110E-XT 0.82 Kg 1.8 lbs eXP-1S110L-XT 0.79 Kg, 1.7 lbs eXP-4S110L-XT 0.82 Kg 1.8 lbs
Shipping Dimensions 20 x 30 x 7 cm, 7.9 x 11.8 x 2.8 inches
Regulatory Approvals
Emissions CISPR 32 / EN 55032 IEC/EN 61000-3-2 IEC/EN 61000-3-3
Immunity CISPR 35 / EN 55035 IEC/EN 61000-4-2 IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 IEC/EN 61000-4-11
Electrical Safety UL/EN/IEC 62368-1 CAN/CSA C22.2 No. 62368-1 UL 60950-1 IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 CSA C22.2 No. 60950-1